MinimalLectures < AFNOG

Tags: view all tags

---+ Lecture notes
---++ Summary:
   * Introduction (this page)
   * [[Communicating with the ESP32]]
   * [[First Python Programs]]
   * [[Modules and Timing]]
   * [[Hardware Access GPIO]]
   * [[Analogue Signals]]
   * [[rgb LED chain]]
   * [[a small project]]
   * [[Building a weather station]]
   * [[The Stepping Motor]]
---++ Introduction

During the exercise sessions, we will first develop a program that lights the user programmable LED on the CPU card. This displays a binary signal, which can only be high or low. The exercise therefore demonstrates how to output a signal and how to control a single digital signal line.

<img alt="esp32V1.png" height="410" src="%ATTACHURL%/esp32V1.png" title="esp32V1.png" width="313" />

On the bottom right of the photo, you see 2 LEDs. The lower one marked ON (upside down) shows if power is supplied to the board, the upper one is user programmable.

As a second exercise we will read a digital actuator, namely a simple push button switch, and we will display its current value (_pushed_ or <i>released) </i>on the PC screen. This exercise therefore demonstrates how to acquire the state of a digital signal. After that, we may switch the LED on, when the button is pressed, and switch it off, when the button is released, thus combining the acquisition of a digital sensor with the display of its state.

<img alt="pushbutton.png" height="344" src="%ATTACHURL%/pushbutton.png" title="pushbutton.png" width="357" />

A slightly more complex program will allow us to read the signal level generated by an analogue sensor (our potentiometer) and display the signal level on the 7 LED rgb (red, green, blue) display. For this to work, we must first understand how to connect and read the analogue signal using the <b>A</b>nalogue to <b>D</b>igital <b>C</b>onverter (ADC). Then we must find out how an LED on the LED ring can be lit and how to select its color. Finally, we can again combine the two functions into a single program. This will read the signal level from the potentiometer and light one of the LEDs on the LED ring. For lowest signal levels, the top LED is lit in blue (which often represents a cold or low value). If the value is a bit higher, then the second LED is activated in cyan, After that we go clockwise using the colors (blue, cyan, green, yellow, magenta, red, white) where white will be displayed for the highest signal level on the center LED.

| <img alt="slider.png" height="384" src="%ATTACHURL%/slider.png" title="slider.png" width="467" /> | <img alt="leds.png" height="440" src="%ATTACHURL%/leds.png" title="leds.png" width="444" /> |

Unfortunately the !LoLin RGB LED shield is not available any longer and our kits cannot be stocked up with this module. It is however possible to create a similar module using an LED ring together with a !WeMos D1 mini prototype board. This is quite a bit of work and the LED addressing is different. The !LoLin board addresses its LEDs in a clock-wise manner while the LED ring does this counter-clock-wise. With a mapping table, this problem can easily be resolved and the two versions will react the same way.
| <img alt="led_ring_front_small.png" height="281" src="%ATTACHURL%/led_ring_front_small.png" title="led_ring_front_small.png" width="300" /> | <img alt="led_ring_back_small.png" height="308" src="%ATTACHURL%/led_ring_back_small.png" title="led_ring_back_small.png" width="300" /> |
| front view of LED ring | back side of the prototype board |

In the 2024 ASP edition, the !IoT workshop has been extended to 2 1/2 days and we have a few new devices. First of all, we now have real sensors which measure air temperature, relative humidity and the barometric pressure. This will allow us to create a simplistic weather station.
| <img alt="sht30-1.png" height="386" src="%ATTACHURL%/sht30-1.png" title="sht30-1.png" width="327" /> | <img alt="bmp180shield.png" height="253" src="%ATTACHURL%/bmp180shield.png" title="bmp180shield.png" width="302" /> |
| SHT30 temperature and humidity sensor | BMP180 barometric pressure sensor |
Often it is desirable to have a local display to show results without having to transfer data to a remote machine. A cheap monochrome OLED (Organic LED) display is available for the !WeMos D1 mini bus but its resolution of 64x48 pixels is a bit too limited.  

<img alt="oled_64x48.png" height="276" src="%ATTACHURL%/oled_64x48.png" title="oled_64x48.png" width="234" />

It is however easily possible to put an OLED with 128x64 pixels onto a prototype board, which I did for this workshop.
| <img alt="oled_front.png" src="%ATTACHURL%/oled_front.png" title="oled_front.png" /> | <img alt="oled_proto_front.png" src="%ATTACHURL%/oled_proto_front.png" title="oled_proto_front.png" /> | <img alt="oled_proto_back.png" src="%ATTACHURL%/oled_proto_back.png" title="oled_proto_back.png" /> |
| 128x64 pixel monochrome OLED display | display prototype board (front) | display prototype board (back) |

Also the actuators have been extended with a small stepping motor and its driver board and there are exercises to make the motor move forward and backwards in different modes and speeds.
| <img alt="stepping.png" height="368" src="%ATTACHURL%/stepping.png" title="stepping.png" width="369" /> |
| Stepping motor and driver board |
Now that we know what we have to do, let's go for it! [[Communicating with the ESP32]]

- - %USERSIG{UliRaich - 2022-10-14}%

---++ Comments

%COMMENT%

Attachments

Topic attachments
I	Attachment	History	Action	Size	Date	Who
png	bmp180shield.png	r1	manage	74.8 K	2024-03-26 - 10:43	UliRaich
png	esp32V1.png	r1	manage	240.5 K	2022-10-14 - 15:12	UliRaich
png	led_ring_back_small.png	r1	manage	178.6 K	2024-03-26 - 10:36	UliRaich
png	led_ring_front_small.png	r1	manage	155.7 K	2024-03-26 - 10:36	UliRaich
png	leds.png	r1	manage	292.6 K	2022-10-14 - 15:39	UliRaich
png	oled_64x48.png	r1	manage	75.1 K	2024-03-28 - 09:35	UliRaich
png	oled_front.png	r2 r1	manage	267.3 K	2024-03-28 - 09:37	UliRaich
png	oled_proto_back.png	r2 r1	manage	283.9 K	2024-03-28 - 09:37	UliRaich
png	oled_proto_front.png	r2 r1	manage	332.9 K	2024-03-28 - 09:37	UliRaich
png	pushbutton.png	r1	manage	154.5 K	2022-10-14 - 15:12	UliRaich
png	sht30-1.png	r1	manage	168.2 K	2024-03-26 - 10:43	UliRaich
png	slider.png	r1	manage	152.9 K	2022-10-14 - 15:39	UliRaich
png	stepping.png	r1	manage	152.3 K	2024-03-26 - 10:47	UliRaich

Topic revision: r10 - 2024-04-01 - UliRaich