The WeMos D1 mini and its sensor and actuator shields

Introduction

We have seen that the ESP01 can be programmed with micro Python and that there are add-on sensor boards available. However, when we connect the sensor board we loose the serial connection to the PC. This can be corrected by soldering extra connectors to the top of the ESP01 board but this is fiddly and needs good soldering equipment and good soldering skills. The other option is to get access to the ESP01 through WiFi using WebRepl

A better and only slightly more expensive solution (we are talking about ~ 3.5 US$ instead of 2.5 US$) is the Wemos D1 mini board. This boards gives up more I/O connections and many more sensor and actuator shields are readily available on the market.

The processor board

The processor board uses an Espressif ESP8266 processor chip and 4 MBytes of flash are installed on the board.

wemosd1mini.png

You will find a description of the pinout at https://www.likecircuit.com/wemos-d1-mini-pinout

For convenience I copied the basic information here.

d1MiniPinout.png

In contrast to a PC the WeMos D1 mini has only very limited memory resources. While 4 MBytes of flash memory is rather comfortable, the amount of RAM (80 K) is a very limiting factor. When running micro Python a mere 30 kBytes is left for your Python programs. There are essentially 2 ways to make most out of the small amount of RAM:

  • You can pre-compile your programs to byte code, which takes less space in RAM
  • You can code freeze driver libraries, which means you integrate their byte code into The micro Python image. This however means that you must compile your own version of micro Python and flash it into the WeMos D1 CPU.
A big number of sensor and actuator boards are available. You will find a complete list with their description at https://wiki.wemos.cc/products:d1_mini_shields

Here are the sensor shields and their test programs for the workshop:

Here is an overview table showing the devices and the
Module Connections Functionality
1 button shield D3: GPIO 0 on / off push button
WS2812B RGB shield D2: GPIO 4 addressable rgb LED

DS1307 RTC and data logger

D1: GPIO 5 I2C SCL
D2: GPIO 4 I2C SDA

D5: GPIO 14 SPI Clock
D6: GPIO 12 SPI MOSI
D7: GPIO 13 SPI MISO
D8: GPIO 15 SPI CS

Real Time Clock

SD card interface

Buzzer shield D5 (default GPIO 14
D6 GPIO 12
D7 GPIO 13
D8 GPIO 15
passive buzzer
BMP180 shield D1 GPIO 5 I2C SCL
D2 GPIO 4 I2C SDA
I2C barometric pressure sensor and
temperature sensor
DHT11 shield D4 GPIO 2 temperature and humidity sensor
OLED shield D1 GPIO 5 I2C SLC
D2 GPIO 4 I2C SDA
64x48 pixel display with SSD1036 I2C controller
DD18B20 shield D2 GPIO 4 1-wire digital temperature sensor
SHT30 shield D1 GPIO 5 I2C SCL
D2 GPIO 4 I2C SDA
I2C temperature and humidity sensor
LED Matrix shield D5 GPIO 14 CLK
D7 GPIO 13 Din
8x8 LED Matrix
ir connections:

For each of the devices I create 2 directories:

  • a driver directory containing programs testing the module without Cayenne communication
  • a cayenne directory for the final program

Comments

Topic attachments
I Attachment History Action Size Date Who CommentSorted descending
PNGpng d1MiniPinout.png r1 manage 542.9 K 2019-03-20 - 09:27 UliRaich  
PNGpng wemosd1mini.png r1 manage 313.5 K 2019-03-20 - 09:20 UliRaich  
Edit | Attach | Watch | Print version | History: r13 | r7 < r6 < r5 < r4 | Backlinks | Raw View | Raw edit | More topic actions...
Topic revision: r5 - 2019-03-25 - UliRaich
 
  • Edit
  • Attach
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2024 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback