Installing a Foswiki Server This page explains how to install a Foswiki server like the one hosting this course. The steps match how this site is set up: Foswiki ...
Introduction to C programming Lecture 3 CSC321: Embedded Systems First Semester 2018/2019 Programming Languages * A programming language is a vocabulary and s...
The BMP180 Temperature and Atmospheric Pressure Sensor The BMP180 is a sensor that measures temperature to 0.1 °C precision and barometric (atmospheric air) press...
* Very often embedded systems do not have a keyboard, mouse and screen attached to them but they must live with more rudimentary (and much cheaper) input/output d...
Solutions to the exercises This is the page to which the solutions will be uploaded. These will mainly consist of gzipped tar files which you can download and unp...
Digital to Analogue Conversion: the mcp4275 Lecture 9 CSC321: Embedded Systems First Semester 2018/2019 Analogue versus digital Up to now we only treated digi...
Stepping Motors Lecture 9 CSC 321: Embedded Sysytem First Semeter 2018/2019 The 27BJY 48 stepper motor and its ULN 2803 driver module A lecture on youtube Th...
Accessing the Real World CSC321: Embedded Systems First Semester 2018/2019 Accessing Libraries The Raspberry Pi flat cable connector and the cobbler bread boar...
Exercises 4 The Raspberry Pi Goal: The Raspberry Pi in contrast to the PC uses and ARM processor and peripherals are not included in the system but are connected...
The Raspberry Pi CSC321: Embedded SystemsFirst Semester 2018/2019 Versions There are several versions of Raspberry Pis available on the market: * The first g...
Implementing the Arduino toolbox The program structure As you would probably expect, the program will consist of three parts * a server running on the Arduino...
Interfacing Scilab to the Raspberry Pi or the Arduino Introduction Scilab is a system for open source program for numerical mathematics quite similar to Matlab e...
Overview The Embedded Systems course at the University of Cape Coast, Ghana, was first offered in 2017. It focuses on data acquisition and control using networked...
Accelerometers Introduction Accelerometers are used in many portable devices like smart phones, to detect if the device is held vertically or horizontally, in fi...
Additional Sensors The sensor kit was originally designed to be used with the Arduino, an Italian micro controller design very popular with hobbyists. The Arduino...
Solutions to the programming exercises Hello World When learning C almost everybody comes across a program called "Hello World". This is the most simple C progra...
The 2 Line LCD Display and its HD44780 Controller Lecture 10 CSC321: Embedded Systems First Semester 2018/2019 Why a simple 2 line display? Often embedded syste...
The MCP4725 Digital to Analogue converter Exercise 1: Once the Digital to Analogue Converter (DAC) is correctly connected to the Raspberry Pi I2C interface the i...
The ADS1115 16 bit ADC The ADS1115 from Texas Instruments is a high precision I2C controlled Delta Sigma ADC. In addition to the ADC itself which provides 2 diffe...
Solutions to exercise 5: Accessing the real world Exercise 5.2: The gpio command The gpio command has many options of which * mode * write * blink are t...
Solutions to Exercise 7: Stepping motors Exercise 7.2 7.3: The different stepping modes The solutions to this exercise are very similar to the solution to the ...
Solutions to exercise 6: The DHT 11 temperature and humidity sensor Exercise 6.0 Using the library This is of course the easiest way to access the DHT11 because ...
Solutions to the assignment on Buzzer and RGB LED The RGB LED The RGB LED consists in fact of 3 tiny LEDs in the basic colors red, green and blue. In the solutio...
Assignment: Buzzer and RGB LED: Exercise 1 Write a program for the active buzzer to buzz using the skeleton below. define pin number int main(void){ initialize ...
Assignment: Buzzer and RGB LED: Exercise 1 Write a program for the passive buzzer to buzz using the skeleton below. define pin number int main(void){ initialize...
Exercise 6 Measuring Temperature and Humidity Goal: The DHT11 is a low lost humidity and temperature sensor using its own serial protocol for data transfer. W...
DHT11 Temperature and Humidity Sensor CSC321: Embedded Systems First Semester 2018/2019 A single GPIO pin We have seen how we can drive an LED from a single ...
Exercises 5: First Hardware Exercise: The LED Goal: Now that we know how to program the Raspberry Pi we will start to setup our first electronic circuits, alb...
Solutions to exercise 4: The Raspberry Pi Most of the exercises refer to exercises we have done in the sessions before on the PC and there are therefore no furthe...
Solutions to exercise 3: Development tools Exercise 3.1: A Makefile for the "Hello World!" program For the simplest possible C program let's write the simplest p...
Exercises 3 Development Tools Goal: This exercise session should get you acquainted with the tools we will use for editing, compiling, running and debugging prog...
Development Tools CSC321: Embedded Systems First Semester 2018/2019 The Development Cycle * In software engineering, a software development cycle is the proce...
The joystick The joystick consists of 2 potentiometers which are read through two ADCs. On the Arduino we use the built in 10 bit ADCs giving us values of 0..1024...
Solutions to the exercises This is the page to which the solutions will be uploaded. These will mainly consist of gzipped tar files which you can download and unp...
Lecture Slides This page contains all the lecture slides: For more information please contact: uli.raich #64;gmail.com Lecture Exercise Solution Lecture...
The Linux Operating System Lecture 2 CSC 321: Embedded Sysytem First Semester 2018/2019 Starting the Linux System This is how the screen for ubuntu 18.04 may loo...
CSC 321: Embedded Systems University of Cape Coast 2018/2019 Academic Year, Semester One Lecture 1 Outline: * Introduction of Lecturers * Isaac Armah M...
Exercises in Python One way to develop the course in a new direction is the replacement of the C programming language by Python. You should not be mislead however...
Tutor Sessions This contains exercises for the UCC staff to get acquainted with Ubuntu Linux, the Raspberry Pi hardware and Raspbian OS, cross compilation, ARM em...
Exercise List Here is a list of exercises to be solved during the course on emdedded systems. First we play on the Linux system installed on the PC, then we write...
Exercise 15: EEPROM and Driver Access Goal: The goal of this exercise is twofold: First we will learn about an EEPROM, a Electrically Erasable Read Only Memory. ...
Measuring temperature and humidity Goal: The DHT11 is a low lost humidity and temperature sensor using its own serial protocol for data transfer. While for 1 wir...
Examination projects on Embedded Systems, Physics class I expect that you solve the problems on your own and you do not copy from your colleagues. For the examin...
The mcp4725 Digital to Analogue Converter Goal: The digital to analogue converter is a device very often used in control applications. Some HV power supplies are...
Analogue to Digital Conversion (ADC) Goal: Apart from the digital to analogue converter where we created analog signal levels from digital values, we have only h...
Exercises 5: First Exercise on Hardware: LEDs Goal: Now that we know how to program the Raspberry Pi we will start to setup our first electronic circuits, albeit...